Skip to main content

Repair iPhone 6 overheating and won't boot

A Japanese version of the iPhone 6, the customer says the iPhone battery has been replaced, it can go into IOS before, but not now; Sometimes have the WIFI and Bluetooth, but sometimes haven’t; the iPhone battery consumption is fast, and iPhone is overheating.


Comprehensive information provided by customer, we think this is caused by the damage to the iPhone WiFi chip. The iPhone can be powered on before, but not boot now, mostly because the batteries are running out.

Using JM-9102 Disassemble Tools to dismantle the iPhone, test the battery, it's really running out of power. Just leave it alone first，and supply power on the iPhone motherboard.


As shown above picture, it's leaking 200mA. Now measure the diode data of VCC_MAIN with Fluke 15B+ Digital Multimeter, as shown in the following picture


Judging from the test results, the diode data of VCC_MAIN is low. Think of the customer before said WiFi sometimes good sometimes bad, so we directly remove the iPhone Wifi Module IC.


After removing the WIFI chip, measure it again, now the diode data of VCC_MAIN is back to normal. Using DC power supply to provide the power to iPhone motherboard to test.



The iPhone standby current is normal, no more leakage. Find new WiFi chip and install it, the boot current also normal. Directly assemble the iPhone, the charging current has 1A, which means the previous judgment is correct. After booting, the WIFI and Bluetooth are available.

Comments

Post a Comment

Popular posts from this blog

User Manual: JC V1 Programmer to fix iPhone light sensor/vibrator

As we know, the light sensor and vibrator is very important for iPhone screen. If you want to replace the iPhone screen, you also need to transfer the original screen data to the new iPhone screen(iPhone 8 to iPhone Xs Max),so you can make sure the new iPhone screen will work fine. Here is a  JC V1 programmer  to fix iPhone light sensor and vibrator problem (for iPhone 7- iPhone Xs Max), it also can repair iPhone baseband eeprom IC or iPhone logic eeprom IC problem. The JC V1 Programmer comes with 24-inch HD display screen, three-color LED indicator light, two small connecting seats (for connecting function panel) , two buttons and one function panel (including light sensor/touch connector, baseband function connector, vibration connector) It support 2 languages (Chinese/English) and three lines of code (read/write/burn/save), the function panel can be changed, the software can automatically update What’s the functions? - Repair iPhone Light sensor/ true ...
1 comment
Read more

Essential tools for a phone repair technician Everyday Use

Must-Have tools for a phone repair technician include precision screwdrivers, spudgers, tweezers, suction cups, and heat guns or hair dryers. Additionally, anti-static mats and wrist straps are crucial for protecting sensitive electronics. Other helpful tools include a multimeter, soldering iron, magnifying lamp or microscope, and various cleaning supplies.  Whether you're a DIY enthusiast or a professional technician, having the right tools is crucial for successful phone repair. Here's a breakdown of common phone repair tools, categorized for clarity: I. Essential Opening and Disassembly Tools: Precision Screwdrivers : These are the most fundamental tools. Phones use tiny screws of various types (Phillips, Pentalobe, Torx, Flathead), so a comprehensive set with magnetic tips is highly recommended to avoid stripping screws and losing tiny parts. Spudgers ( Pry Tools ): Made of plastic or nylon, these non-conductive tools are invaluable for safely prying open phone casings...
Post a Comment
Read more

How to install K-TAG 7.003 KTM100 K-Suite 2.13 software

China Clone KTAG 7.003 firmware has newly launched, New2.13 KTM100 software is the replacement of 2.13 K-Suite which brings brand-new interface and makes easier operation. Here, vipprogrammer.com share the installation guide of K-TAG 7.003 K-Suite 2.13 software, this step-by-step instruction guide will help you. Software: KTM100 V2.13 (better than Ksuite software) Firmware: V7.003 Language:  English, Italian, Portuguese NOTE: KTM100 software can only be work with KTAG firmware V7.003 New KATG KTM100 V2.13 Firmware 7.003 new added feature: 1) New add BMW F chassis petrol and Mercedes-Benz W222 models 2) Software is much easier to use and is very stable. After you connect the car, just choose the large type, KTM100 will recognize the ECU detailed type via ID automatically. Disable both local network and wireless connection (Very important!!!) 1) Install KTAG KTM100 V2.13 setup Open KTM100 setup in the CD software on My computer Open KTM100 file, then open KTM100 English file...
Post a Comment
Read more