Skip to main content

DIY Fix iPhone X won't boot issue via repairing motherboard

The customer send us an iPhone X to repair, the fault described is that the iPhone is not turning on after dropping, and it reports error 56 after restoring.


The iPhone X is connected by 2 pieces motherboard via a middle column, so the pins are easy to lose because of dropping. Now, it's possibly the pin from the NFC chip to the iPhone CPU that was dropped off.

Disassemble the iPhone X, take out the iPhone motherboard. Use QUICK 861DW hot air rework station to separate the iPhone X motherboard, and then we saw that there are some pin was dropped off.


Check iPhone schematic diagram via WUXINJI Dongle, it's surrounded by ground lines, and the 6 useful pins was dropped off.

The ground lines are no need to fill, we just need to fill these 6 useful pins, we can check it under the Stereo Zoom Microscope. These all are the signal line of the NFC chip, so when we restore iPhone by iTunes, it reports unknown error 56.


Next we need to plant the tin in the middle column, and then re-weld the AP part.


Install the iPhone motherboard, assemble the iPhone, and then re-flash it again, now it flashes smoothly, all functions tested are normal, the repairs end!

This fault is because of the solder pins that from the signal of the NFC chip pass through the middle column to iPhone CPU was dropped off, and then it causes iTunes error 56 on iPhone. 


Comments

Post a Comment

Popular posts from this blog

User Manual: JC V1 Programmer to fix iPhone light sensor/vibrator

As we know, the light sensor and vibrator is very important for iPhone screen. If you want to replace the iPhone screen, you also need to transfer the original screen data to the new iPhone screen(iPhone 8 to iPhone Xs Max),so you can make sure the new iPhone screen will work fine. Here is a  JC V1 programmer  to fix iPhone light sensor and vibrator problem (for iPhone 7- iPhone Xs Max), it also can repair iPhone baseband eeprom IC or iPhone logic eeprom IC problem. The JC V1 Programmer comes with 24-inch HD display screen, three-color LED indicator light, two small connecting seats (for connecting function panel) , two buttons and one function panel (including light sensor/touch connector, baseband function connector, vibration connector) It support 2 languages (Chinese/English) and three lines of code (read/write/burn/save), the function panel can be changed, the software can automatically update What’s the functions? - Repair iPhone Light sensor/ true ...
1 comment
Read more

How to install K-TAG 7.003 KTM100 K-Suite 2.13 software

China Clone KTAG 7.003 firmware has newly launched, New2.13 KTM100 software is the replacement of 2.13 K-Suite which brings brand-new interface and makes easier operation. Here, vipprogrammer.com share the installation guide of K-TAG 7.003 K-Suite 2.13 software, this step-by-step instruction guide will help you. Software: KTM100 V2.13 (better than Ksuite software) Firmware: V7.003 Language:  English, Italian, Portuguese NOTE: KTM100 software can only be work with KTAG firmware V7.003 New KATG KTM100 V2.13 Firmware 7.003 new added feature: 1) New add BMW F chassis petrol and Mercedes-Benz W222 models 2) Software is much easier to use and is very stable. After you connect the car, just choose the large type, KTM100 will recognize the ECU detailed type via ID automatically. Disable both local network and wireless connection (Very important!!!) 1) Install KTAG KTM100 V2.13 setup Open KTM100 setup in the CD software on My computer Open KTM100 file, then open KTM100 English file...
Post a Comment
Read more

Install instructions for 2015.R1 autocom CDP Diagnosis software

2015.R1 autocom cdp software is available, 2015.1 autocom cdp software need to be activated by keygen, here, we share Install instructions for 2015.R1 autocom cdp software, help you how to crack autocom cdp software on you pc Tips: 1.) TURN OFF your internet connection! 2.) Shutdown antivirus software! The tutorial of Installing 2015.R1 autocom cdp Step 1: download autocom cdp software or insert the dvd to your pc. Step 2: pls download upgrade file for 2015.1 autocom cdp software, then copy all file and folder replace to autocom cdp(new vci) install Folder. Instructions for 2014.R1 autocom cdp Diagnosis software Step 3: Run autocom cdp software agian, the Activation menu will be showed, PLS DO IT by activation guide for 2013.R3 autocom cdp software. Step 4: Choose - click “YES” button to save autocom cdp FileActivation file, send this FileActivation.xml file to us (PLS DON’T USING 2013.3 Autocom delphi KEYGEN GET Activation FILE). Instructions for 2015.R1 autocom cdp Diagnosis softwar...
8 comments
Read more