Skip to main content

Best fix iPhone 6S Plus many issues after dropped

A customer sent us an iPhone 6S Plus to repair,  the issue is that the iPhone accidentally dropped into the ground, and then the iPhone has been badly hurt, such as iPhone rear camera, WiFi, audio, volume, photoreceptor, card setting all has problem. How to best fix it? Keep reading.



It can be turned on when using multimeter to trigger but the current is a bit large. No matter what, we have to turn on the handset and enter into system to have a test.

The first problem is card setting. Continue to test other functions, it is true that the front flex cable, audio key flex cable, and rear camera are all broken, so we have to replace all of the spare parts.

The last fault we need to confirm is motherboard: card setting, bad WiFi, audio recording is not available, bad audio and leakage. Triggered with more than 300 mA current, which means it has problem. Now we should solve the fault one by one.

Since we can't get into the setup, so we take off the iPhone 6s Plus WiFi audio first. The result is the same. There are much solder points are dropped at the bottom of WiFi, it damaged very serious. 30 pin is still on the iPhone 6sp motherboard, but the value is measured with 0L (infinity), certainly it's not normal, so we are going to solder the jumper wire, and also do jumpers on the other disconnected parts.


The jumpers in this repair are easy to do. A tip for new repairman: It's better to leave more jumper outside if there is enough space, so you can extend wire even there are other issues existing.

After soldering jumpers, install the motherboard to test, there is no card setting. We had always thought that only WIFI was not good and that the card was set on the board, and the WIFI would not be stuck. Today, we can see it's same if WiFi is removed off, after intall WiFi, the signal is very weak, it seems that the board layer is broken again, direct solder  jumper wire to the opposite track. 



Now the signal is normal, and then another iPhone 6 plusaudio IC chip can be replaced, the whole repair process is finish here!



Labels:

Comments

Post a Comment

Popular posts from this blog

Complete Guide to Replacing Your iPhone Battery at Home

  Has your iPhone battery started showing the dreaded signs of age, like frequent charging, rapid draining, or even an untimely shutdown? Are you considering a battery replacement but feeling deterred by the potential cost or hassle of a trip to the Apple Store? Don't worry; with the right guidance, you can replace your iPhone battery at home quickly and safely, sparing your wallet and ensuring a future of longer charge cycles for your beloved device. Whether you have the latest model or an older version, we'll walk you through the process step by step. But before we get into the nitty-gritty, here's why a battery replacement might be in your best interest. Why You Should Replace Your iPhone Battery The lithium-ion batteries in our smartphones are not immortal. They degrade over time due to a variety of factors, such as age, temperature, and the number of charge cycles. Replacing an old battery can provide several benefits: Improved Performance: A new battery can result ...
Post a Comment
Read more

User Manual: JC V1 Programmer to fix iPhone light sensor/vibrator

As we know, the light sensor and vibrator is very important for iPhone screen. If you want to replace the iPhone screen, you also need to transfer the original screen data to the new iPhone screen(iPhone 8 to iPhone Xs Max),so you can make sure the new iPhone screen will work fine. Here is a  JC V1 programmer  to fix iPhone light sensor and vibrator problem (for iPhone 7- iPhone Xs Max), it also can repair iPhone baseband eeprom IC or iPhone logic eeprom IC problem. The JC V1 Programmer comes with 24-inch HD display screen, three-color LED indicator light, two small connecting seats (for connecting function panel) , two buttons and one function panel (including light sensor/touch connector, baseband function connector, vibration connector) It support 2 languages (Chinese/English) and three lines of code (read/write/burn/save), the function panel can be changed, the software can automatically update What’s the functions? - Repair iPhone Light sensor/ true ...
1 comment
Read more

Here: JC P11 iPhone Nand Test Fixture Specification Details

JC P11 iPhone Nand test fixture is on sale now, some users still confused for it, what's credit points for JC P11? Why it's cheap? As we know, JC P11 BGA110 programmer is the latest programmer for iPhone   iPhone XS Max,XS, X, 8P, 8  and iPhone 11 Pro max/pro/11, which is made by JCID factory.  Here are some  specification details for JC P11 programmer . 1. Main Functions. - Support to modify and write BGA110 NAND SYSCFG data (NAND Flash underlying data, such as SN/BT/WIFI and others); Unbind WIFI. - It doesn't require restoring the firmware for brand-new Nand flash, the SYSCFG data can be written directly. - Repair the Error 35 during firmware restoring for BGA110 NAND - Repair the DATA Error for BGA110 NAND - Support iPhone 8/8P/X/XS/XS Max currently, free software upgrade to support 11-11Pro Max in the future - Initiate the network charging mode, can purchase the points according to the demand, which greatly saves the equipmen...
Post a Comment
Read more