Skip to main content

Troubleshooting Tips for iPhone 6S won’t leakage and won’t turn on issues

Actually, the iPhone 6S leakage and won't turn on problem is no stranger to us. Here , we have some troubleshooting tips for these issues.  After check iPhone schematic diagram on WUXINJI Dongle, we know that the iPhone 6S battery voltage passes the charge IC and then output the main power supply VCC_MAIN.

First, we introduce two common scenarios.  One is BATT_VCC (battery voltage) or VCC_MAIN (main power supply) these two circuit lines short circuit causes iPhone leakage when provide power on it. The other one is damaged USB control IC causes iPhone standby current is about 100mA.

If provide power on iPhone but is shows leakage or large current, then we need to use Fluke 15B+ DigitalMultimeter  to measure the diode data of BATT_VCC and VCC_MAIN! If there is a short circuit, we can apply some rosin on the iPhone motherboard component, use hot air gun to smoke it, and supply voltage on short circuit line, the voltage starting from 0 and gradually increasing, and then you can find the short circuit parts. In this part, we have to add voltage on short circuit place.

The other iPhone power leakage situation is that when you provide power on it, it won't leak, but after you press the iPhone power button, the leakage or large current fault happens. This fault is because there is a leakage component on the circuit lines that was output by power supply IC. In this case, you need to measure the diode data of each circuit line to find the one that's leaking. If the leakage is large, you can use rosin methods to find the short circuit parts (the methods the same as above).


In addition to the leakage of the situation caused iPhone no boot, there are other reasons cause iPhone won't boot.

1. Reports different iTunes error. If it reports iTunes error 4005/ 4014/ 9/ 14/ 40, usually it is caused by iPhone Nand flash or iPhone CPU. Because the iPhone CPU is unable to weld, you can re-install it or replace the Nand flash, and then flash it again. If it reports iTunes error 1/47/48/50, usually it is baseband part problem; you can re-install iPhone baseband CPU and power IC. Moreover, damaged compass will cause iTunes error 4013, just replace the compass IC. If it reports iTunes error 56, mostly it's caused by NFC module virtual welding or damaged. If baseband power IC is virtual welding, you can re-install or replace it.

2. Stuck on White Apple logo when booting. Replace the USB control IC U4500 charge IC U2300. If the fault still exists after replacement, then it should be the CPU or NAND flash problem, you can re-install the iPhone NAND flash.

3. No response when booting. Measure whether these is a VCC_MAIN, if not, replace the charge IC U2300, if VCC_MAIN is normal, and then replace the power IC U2000.

4. Stuck on Dozens of MA when booting. This fault mostly caused by CPU or iPhone NAND flash virtual welding or damaged. For water damaged iPhone, you can replace power IC/ audio IC/ compass IC/ iPhone USB control IC/ charge IC.




Labels:

Comments

Post a Comment

Popular posts from this blog

User Manual: JC V1 Programmer to fix iPhone light sensor/vibrator

As we know, the light sensor and vibrator is very important for iPhone screen. If you want to replace the iPhone screen, you also need to transfer the original screen data to the new iPhone screen(iPhone 8 to iPhone Xs Max),so you can make sure the new iPhone screen will work fine. Here is a  JC V1 programmer  to fix iPhone light sensor and vibrator problem (for iPhone 7- iPhone Xs Max), it also can repair iPhone baseband eeprom IC or iPhone logic eeprom IC problem. The JC V1 Programmer comes with 24-inch HD display screen, three-color LED indicator light, two small connecting seats (for connecting function panel) , two buttons and one function panel (including light sensor/touch connector, baseband function connector, vibration connector) It support 2 languages (Chinese/English) and three lines of code (read/write/burn/save), the function panel can be changed, the software can automatically update What’s the functions? - Repair iPhone Light sensor/ true ...
1 comment
Read more

Essential tools for a phone repair technician Everyday Use

Must-Have tools for a phone repair technician include precision screwdrivers, spudgers, tweezers, suction cups, and heat guns or hair dryers. Additionally, anti-static mats and wrist straps are crucial for protecting sensitive electronics. Other helpful tools include a multimeter, soldering iron, magnifying lamp or microscope, and various cleaning supplies.  Whether you're a DIY enthusiast or a professional technician, having the right tools is crucial for successful phone repair. Here's a breakdown of common phone repair tools, categorized for clarity: I. Essential Opening and Disassembly Tools: Precision Screwdrivers : These are the most fundamental tools. Phones use tiny screws of various types (Phillips, Pentalobe, Torx, Flathead), so a comprehensive set with magnetic tips is highly recommended to avoid stripping screws and losing tiny parts. Spudgers ( Pry Tools ): Made of plastic or nylon, these non-conductive tools are invaluable for safely prying open phone casings...
Post a Comment
Read more

How to restore & unlock the apple watch series 1, 2, 3, 4, 5, and 6?

  Can you always remember your password? What should you do when there is a red exclamation error on your Apple watch after update you iWatch？6 IN 1   AWRT iBus   Tools, a professional Apple Watch recovery tool, enables you to unlock, repair and remove the exclamation error easily.   Why choose the AWRT iBus tool? Perhaps you would tell me Apple support team can solve the trouble. While they may help, you may not be patient enough because you want your watch fixed immediately. Moreover, you don't have to wait for too long for them to help you solve the issues. 1. This incredible device has an inbuilt original restore adapter for the apple watch of the series S1, S2, S3, S4, S5, and S6 42 mm and 38 mm /$199. There are also S1-just 38MM /$39.99, Adapter for S1-42mm 38mm /$139.99, or Adapter for S2 S3 - 42mm 38mm /$169.99 version for choosing. The tool requires professional Apple Watch Firmware  IPSW File  for iWatch S1-S6. 2. Moreover, the iBus tool has a lot...
Post a Comment
Read more